$47.25 - $92.99
No Sales Tax, Except CT
View Customizable Drawer Inserts Here
- Rev-A-Shelf Cut-To-Size Insert Peg System for Drawers
- Material: UV Cured Maple Construction
- Can be Trimmed to Fit
- Small Drawer Peg System: Includes Cut-to-Size Board and 9 Matching Push-In Pegs
- Medium Drawer Peg System: Includes Cut-to-Size Board and 12 Matching Push-In Pegs
- Large Drawer Peg System: Includes Cut-to-Size Board and 16 Matching Push-In Pegs
- Organize all Kinds of Items from Dinner Plates to Plastic Containers with Dividers for your Drawers
- Limited Lifetime Manufacturers Warranty
- Additional Wood Pegs Available, See Accessories Below to Purchase
The Drawer Peg Systems by Rev-A-Shelf will organize all kinds of items from dinner plates to plastic containers with dividers for your drawers. These peg systems are constructed from maple that is UV-Cured and comes with matching, push in pegs. The small peg system comes with 9 pegs, medium peg system comes with 12 pegs and the large peg system comes with 16 pegs. Ships via UPS/FedEx Ground.
(W = side to side) (D = front to back) (H = top to bottom)
Small Board for Cabinets 27" W or Smaller: 24-1/4" W x 21-1/4" D x 6-5/8" H
Medium Board for Cabinets 30" W or 33" W : 30-1/4" W x 21-1/4" D x 6-5/8" H
Large Board for Cabinets 36" W, 39" W or 42" W: 39-1/4" W x 21-1/4" D x 6-5/8" H
Ships via UPS/FedEx Ground
by: Nancy from: West Richland, Wa on: September 26, 2016
| ||The peg board system I ordered came quickly and exceeded expectations.
I would not hesitate ordering from Kitchen Source again.
|First time to use - seems good.
by: Michael Ray from: Fredericksburg, Te on: April 25, 2016
| ||Nice looking product. The only negative I see to the product is that the pegs fit so tightly it actually tears the plywood veneer on the hole somewhat when you pull a peg out to move it to a different hole.
by: lfaryna from: -, NY on: July 10, 2009
| ||I have my table dishes in a deep drawer that was custom made for me. The dishes tended to slide around as the drawer was opened and closed making it very hard on the hardware. The Pegs are great and the board was almost exactly the right size, needed just a small amount of trimming to fit. I can arrange and rearrange the pegs until i get them in the right place. perfect Solution
|Just what I needed
by: L F from: -, NY on: June 11, 2009
| ||I keep all my table dishes in a deep drawer made for the purpose but they slid around when the drawer was opened and closed. The peg board stabilizes the stacks and saves wear and tear on the hardware. It is beautifully finished, and after trimming with a table saw dropped right into place. I added the pegs where they would work best and it is great! The only thing I might change would be to make the peg holes closer together to allow for different spacing.
|How thick is the peg board? - Asked about product RV-4DPB-2421
| ||The peg board is 5/8” thick.
| ||0% of 0 people found this useful. Was this useful to you? Yes (0) | No (0)|
|How far apart are the holes in the peg board? - Asked about product RV-4DPS-3921
| ||2-1/2’’ from center to center.
| ||100% of 3 people found this useful. Was this useful to you? Yes (3) | No (0)|
This item(s) is also sometimes listed under the following manufacturer numbers:
4DPS-2421, 4DPS-3021, 4DPS-3921, 4DPB-2421, 4DPB-3021, 4DPB-3921