We carry a full range of Storage Accessories - call us at 1-800-667-8721 if you don't see the item you want.

Iron-A-Way Installation Instructions
| Recessed Mounting | Surface Mounting |

Recessed Mounting
Extends Into Room Approximately 3"
Model NE-242A Not Available for Recessed Mounting

A. Determine desired ironing board height above the floor using the chart below labeled C1. Cut opening between studs as shown taking care the cutting will be mounted at the ironing board height desired.

B. Door opens approximately 180º. Allow at least 16" to side of cabinet door to swing open.

C. Attach 2" x 4" cleats to studs, level with the bottom of opening.

D. Pre-drill pilot holes through the cabinet frame as indicated starting approximately 14" from top of cabinet and 24" apart. Attach cabinet to studs with #12 x 1½" screws through sides of cabinet.

E. Plumb Cabinet and shim to fit.

 
C1 - Required Opening Size
Model Opening
A-46A 14 1/4" x 59 7/8" x 3 7/8"
A-42A 14 1/4" x 47 1/8" x 3 7/8"
E-342A 14 1/4" x 47 1/8" x 3 7/8"
NE-342A 14 1/4" x 47 1/8" x 3 7/8"

Electrical
ALL ELECTRICAL WORK MUST BE DONE IN ACCORDANCE WITH ALL APPLICABLE ELECTRICAL CODES.

TURN OFF POWER AT SERVICE ENTRANCE BEFORE INSTALLING, WIRING OR SERVICING THIS PRODUCT.

F. Pigtails are provided in bottom of wireway for hookup to supply line. Make entrance into knockouts provided in top and bottom of wireway through left-hand vent hole.


.


Wiring Diagram
115/120 Vac 15 AMP:
A. Pilot Light
B. Timer or toggle type on/off switch
C. Grounded outlet
D. Cut off switch activated by board when in upright position
E. Optional spotlight when used

Surface Mounting
NE-242 Extends Into Room Approximately 3"
All Other Models Extend into Room Approximately 6 7/8"

A. Determine desired ironing board high above the floor using the chart below labeled C2. Care should be taken to insure the unit will be mounted at the ironing board height desired.

B. Locate wall stud to be used for mounting. Stud should be located as close to center of cabinet as possible

B.1) For NE-242A: Using a 1/4" drill bit pre-drill holes through upper and lower cross frames where anchoring screws will be located. It is recommended to countersink anchoring screws and when the mounting location is not centered on the stud, two screws in both cross frames is desirable. (Caution: Do not pre-drill wall with 1/4" drill bit. See D for wall instructions.

B.2) All other models: Using a 1/4 drill bit pre-drill holes into upper and lower cabinet cross braces where the lag screws will be located.

C. Allow at least 16" to side of cabinet for door to swing open. Door opens approximately 180º

D. Using a 3/16 drill bit pre-drill a pilot hole into a wall stud where the cabinet will be attached to the wall.

E. Attach a cabinet to wall by inserting the lag screws included for mounting through the predrilled holes in the cabinet cross frames or braces and screw into predrilled pilot holes in wall stud.


C2 - Mounting Height Above Floor Level
Designed
Board
Height

A-46A*

A-42A*
E-342A Swivel*
NE-342A Swivel *

E-342A
NE-342A
NE-242A

(Mount Cabinet Above Floor)

38" 24" 30" 32"
37" 23" 29" 31"
36" 22" 28" 30"
35" 21" 27" 29"
34" 20" 26" 28"
33" 19" 25" 27"
32" 18" 24" 26"
31" 17" 23" 25"
30" 16" 22" 24"
29" 15" 21" 23"
28" 14" 20" 22"
*Note: The user can adjust height of board after installation with a 4" differential between a maximum and minimum height. Figures under left column are for normal default position.

Electrical
ALL ELECTRICAL WORK MUST BE DONE IN ACCORDANCE WITH ALL APPLICABLE ELECTRICAL CODES.

TURN OFF POWER AT SERVICE ENTRANCE BEFORE INSTALLING, WIRING OR SERVICING THIS PRODUCT.

F. Pigtails are provided in bottom of wireway for hookup to supply line. Make entrance into knockouts provided in top and bottom of wireway through left-hand vent hole.